Want to Factory Reset Netgear Nighthawk Router? Try This!

Reset Netgear Nighthawk Router
If your Netgear Nighthawk router acting weird or you can’t access the Netgear Genie login page using routerlogin credentials, then the only solution you are left with is to reset your Netgear Nighthawk router back to the default factory settings.

Over time, 3 out of 5 users often face issues with their Netgear Nighthawk routers. Such issues may range from poor internet connectivity to uninterrupted WiFi signals. In such a case, it becomes crucial for you to reset your Netgear Nighthawk router back to the default factory settings.


Before you reset your Netgear Nighthawk router – it is important for you to be aware of the fact that the process erases all the personalized information and data on your device including routerlogin Nighthawk details. So, in order to configure your Netgear device again without any hassle, ensure to have a back up of the data from your end.


Once you’re done with having the back up of your Netgear Nighthawk router, below are the steps you need to follow for resetting your Netgear device to default settings. Scroll down a little!


Reset Netgear Nighthawk Router


Here’s how to reset Netgear Nighthawk router!


There are 2 easy methods to take your Netgear Nighthawk router back to the factory default values. You can either use hard reset or soft reset method to take your device back to the default values. Let’s make you familiar with both the methods one-by-one. Keep scrolling down!


How to Soft Reset Netgear Router?


Follow the steps highlighted to factory reset your Netgear Nighthawk router:


Step 1: First and foremost, make sure that the LEDs on your Netgear Nighthawk router are lit and green. In the event that the LED on the device is blinking for too long, wait till it becomes stable.


Step 2: Log in to your Netgear router using the default 192.168.1.1 IP or routerlogin.net web address.


Step 3: Now, navigate to Netgear Genie setup wizard.


Step 4: Locate the Reset option. Once found - click on it, confirm your decision and wait for a couple of minutes till your Netgear Nighthawk router resets back to the default factory settings.


After you reset your Netgear router, ensure to configure it again using the default routerlogin admin name and password to enjoy the lag-free internet throughout your house.


How to Hard Reset Netgear Router?


To hard reset your Netgear Nighthawk router, do the following:


Step 1: First things first, ensure that your Netgear Nighthawk router is getting steady power supply from its respective wall outlet. Do not use a damaged or fluctuated wall socket to plug in your Netgear Nighthawk router.


Step 2: Don’t forget to disconnect your Netgear Nighthawk router from all the connected devices in your home, including modem.


Step 3: Now, locate the reset hole on your Netgear Nighthawk router and press it gently using a pin, oil pin, paper clip or any similar object.


Step 4: Hold the reset hole of your device for some time and release it.


Step 5: The power LED on your Netgear Nighthawk router will start blinking and become green and stable after a couple of minutes.


Kudos! In this way, you can hard reset your Netgear Nighthawk router with ease. Now, you can access the Netgear Genie setup wizard page using the default 192.168.1.1 IP or routerlogin.net web address and configure it again.


Note: To prevent Netgear router not working issue - bear in mind to perform the reset process correctly.


The Bottom Line


On the off chance if you failed or facing issues while resetting your Netgear Nighthawk router using the hard reset or the soft reset method, without much delay, drop your questions into the comments section.


Read more : 192.168.1.250 IP Not Working? Let’s Get It Fixed!